Zyxel Kennetic Giga нет сети
Попал ко мне данный аппарат с диагнозом "не удалось настроить интернет".
На деле оказалось, что к роутеру нет доступа через LAN порты, только через WiFi.
Настройки неоднократно сбрасывались, шились разные прошивки. И с первой и со второй версией роутер ведёт себя одинаково: через LAN нет доступа к 192.168.1.1, сам роутер не видит сеть интернет. Само собой, пришла первая мысль, что сдох роутерный гигабитный свитч, но ведь при втыкании кабеля лампочка загорается и в веб-интерфейсе правильно показывается скорость и дуплекс.
Есть надежда оживить его?
Keenetic Giga: CPU: RT3052 MIPS24Kc @384MHz Flash: 8MB RAM: SDRAM 32bit 64MB
WLAN: Built in SoC 2T2R/300Mbps (2.4GHz) Switch: 5x1GbE with HW_NAT v1 USB: 2x2.0
Вот лог загрузки:
На деле оказалось, что к роутеру нет доступа через LAN порты, только через WiFi.
Настройки неоднократно сбрасывались, шились разные прошивки. И с первой и со второй версией роутер ведёт себя одинаково: через LAN нет доступа к 192.168.1.1, сам роутер не видит сеть интернет. Само собой, пришла первая мысль, что сдох роутерный гигабитный свитч, но ведь при втыкании кабеля лампочка загорается и в веб-интерфейсе правильно показывается скорость и дуплекс.
Есть надежда оживить его?
Keenetic Giga: CPU: RT3052 MIPS24Kc @384MHz Flash: 8MB RAM: SDRAM 32bit 64MB
WLAN: Built in SoC 2T2R/300Mbps (2.4GHz) Switch: 5x1GbE with HW_NAT v1 USB: 2x2.0
Вот лог загрузки:
Код:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.12.19 21:06:28 =~=~=~=~=~=~=~=~=~=~=~=
U-Boot 1.1.3 (Mar 29 2012 - 20:20:57)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
config usb..
flash_protect ON: from 0xBF000000 to 0xBF01A4C3
flash_protect ON: from 0xBF030000 to 0xBF030FFF
============================================
Ralink UBoot Version: 3.3.4_ZyXEL_AR8316
--------------------------------------------
ASIC 3052_MP2 (Port5<->GigaSW_AR8316)
DRAM component: 256 Mbits SDR
DRAM bus: 32 bit
Total memory: 64 MBytes
Flash component: NOR Flash
Date:Mar 29 2012 Time:20:20:57
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
SDRAM bus set to 32 bit
SDRAM size = 64 Mbytes
Firmware test register status: 0x00000000
Switch AR8316 found in MAC mode.
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
4 3 2 1 0
3: System Boot system code via Flash.
## Booting image at bf050000 ...
Image Name: ZyXEL KEENETIC Series
Created: 2012-05-29 21:24:32 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1188781 Bytes = 1.1 MB
Load Address: 80000000
Entry Point: 8033b000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8033b000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.23.17 (developers@ndmsystems.com) (gcc version 4.1.2) #1 Wed May 30 01:21:03 MSK 2012
The CPU frequency set to 384 MHz
64M RAM Detected!
CPU revision is: 0001964c
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Built 1 zonelists in Zone order. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 40808068, status = 11000000
PID hash table entries: 256 (order: 8, 1024 bytes)
calculating r4koff... 0005dc00(384000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61348k/65536k available (2726k kernel code, 4128k reserved, 578k data, 128k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
fuse init (API version 7.8)
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: module loaded
MAC_ADRH -- : 0x00000000
MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
MAC_ADRH -- : 0x0000000c
MAC_ADRL -- : 0x43288048
PROC INIT OK!
Switch AR8316 found in MAC mode.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.4
PPTP driver version 0.8.3.37
ralink flash device: 0x800000 at 0x1f000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 7 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "U-Boot"
0x00030000-0x00040000 : "U-Config "
0x00040000-0x00050000 : "RF-EEPROM"
0x00050000-0x00180000 : "Kernel"
0x00180000-0x005f0000 : "RootFS"
0x005f0000-0x00600000 : "Config"
0x00600000-0x00800000 : "Storage"
usbcore: registered new interface driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for airprime
usbcore: registered new interface driver airprime
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
Type NAT: Restricted Cone
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
decode /dev/mtdblock4
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 128k freed
init started: BusyBox v1.8.2 (2012-05-20 00:25:17 MSK)
starting pid 645, tty '': '/etc/rc.sysinit'
Algorithmics/MIPS FPU Emulator v1.5
LED driver vers. 1.7 loaded.
IPP2P v0.8.2 loading
Load Timer Module(Wdg/Soft)
Start powerstat module.
Read power status register: 0x00000000.
Status: Power was turned off.
Write power status register: 0x00000001.
dwc_otg: version 2.72a 24-JUN-2008
DWC_otg: Core Release: 2.66a
DWC_otg: Periodic Transfer Interrupt Enhancement - disabled
DWC_otg: Multiprocessor Interrupt Enhancement - disabled
DWC_otg: Using DMA mode
DWC_otg: Device using Buffer DMA mode
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 18, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (1 port)
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (3 port)
usb 1-1: new high speed USB device using dwc_otg and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new interface driver sierra
rt2860v2_ap: module license 'unspecified' taints kernel.
Configuring network topology
MAC_ADRH -- : 0x0000cc5d
MAC_ADRL -- : 0x4efbb680
phy_tx_ring = 0x03886000, tx_ring = 0xa3886000
phy_rx_ring0 = 0x03887000, rx_ring0 = 0xa3887000
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 710000
No need to change the port 0 setting...
No need to change the port 1 setting...
No need to change the port 2 setting...
No need to change the port 3 setting...
No need to change the port 4 setting...
device eth2.1 entered promiscuous mode
device eth2 entered promiscuous mode
0x1300 = 00064380
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
br0: port 1(eth2.1) entering learning state
Run Fast NAT.
udhcpc (v1.8.2) started
Sending discover...
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth2.1) entering forwarding state
Start swlink module, WAN port 4.
Please press Enter to activate this console. Sending discover...
Sending discover...
Комментарий