List of Access Point CLI commands:
 ?		-- Display CLI Command List
 alpha		-- Temporary factory admin (for RD debug only)
 boot flash		-- Boot from flash
 boot ethernet		-- Boot from network
 cp		-- Copy file
 delpcode		-- Delete Product Code File pcode
 readpcode		-- Reading Product Code from pcode
 setpcode		-- Setting Product Code to pcode
 config wlan		-- config wlanX
 connect bss		-- connect to bssX
 del acl		-- Delete Access Control List
 del wdsacl		-- Delete WDS Access Control List
 del key		-- Delete Encryption key
 find bss		-- Find BSS
 find channel		-- Find Available Channel
 find all		-- Find All BSS
 find rogue		-- Find Rogue BSS
 dhcps help		-- Display DHCP Server Command Help
 dhcps state		-- Display and Set DHCP Server State
 dhcps dynamic		-- Display and Set DHCP Server Dynamic Pool Info
 dhcps static		-- Display and Set DHCP Server Static Pool Info
 igmp state		-- IGMP snooping state
 igmp enable		-- IGMP snooping enable
 igmp disable		-- IGMP snooping disable
 igmp dump		-- IGMP MDB dump
 igmp setrssi		-- set igmp snp rssi threshold
 igmp getrssi		-- get igmp snp rssi threshold
 igmp setportagingtime		-- set igmp snp port aging time
 igmp getportagingtime		-- get igmp snp port aging time
 ipfilter state		-- Display or Set Remote IP Acl State
 ipfilter add		-- Add a IP Range<xxx.xxx.xxx.xxx> <xxx.xxx.xxx.xxx> Entry
 ipfilter del		-- Del a IP Range<xxx.xxx.xxx.xxx> <xxx.xxx.xxx.xxx> Entry
 ipfilter clear		-- Clear IP Pool
 ipfilter list		-- Display IP Pool
 rogue add		-- Add a Rogue Access Point Result <index> Entry
 rogue del		-- Del a Rogue Access Point Result <index> Entry
 rogue deleep		-- Del a Rogue Access Point Result <index> Entry
 rogue list		-- Display Rogue Access Point Detection Result
 rogue listeep		-- Display Rogue Access Point Detection Result
 format		-- Format flash filesytem
 bootrom		-- Update boot rom image
 getimage		-- Flash image upload to PC via FTP
 superftp		-- Software update via FTP
 had		-- Software update HAD file via FTP
 ftp		-- Software update TFP file via FTP
 get 11gonly		-- Display 11g Only Allowed
 get 11goptimize		-- Display 11g Optimization Level
 get 11goverlapbss		-- Display Overlapping BSS Protection
 get abolt		-- 
 get acl		-- Display Access Control List
 get wdsacl		-- Display WDS Access Control List
 get wdsap		-- Display WDS Access Point
 get apmode		-- Display AP Mode(runtime)
 get aging		-- Display Aging Interval
 get antenna		-- Display Antenna Diversity
 get association		-- Display Association Table
 get authentication		-- Display Authentication Type
 get autochannelselect		-- Display Auto Channel Select
 get backup		-- Check Backup Code 
 get basic11b		-- Display Basic 11b Rates
 get basic11g		-- Display Basic 11g Rates
 get basisconnect		-- Display Basis of Connect Mode
 get beaconinterval		-- Display Beacon Interval
 get ratecontrol		-- Display supported datarate state
 get supportrate		-- Display supported datarate
 get burstSeqThreshold		-- Display Max Number of frames in a Burst
 get burstTime		-- Display Burst Time
 get bridgelearning		-- Get bridge learning status
 get cacheperf		-- Display the cache performance counters
 get calibration		-- Display Noise And Offset Calibration Mode
 get cckTrigHigh		-- Display Higher Trigger Threshold for CCK Phy Errors for ANI Control
 get cckTrigLow		-- Display Lower Trigger Threshold for CCK Phy Errors for ANI Control
 get cckWeakSigThr		-- Display ANI Parameter for CCK Weak Signal Detection Threshold
 get channel		-- Display Radio Channel
 get availablechannel		-- Display Available Radio Channel
 get cipher		-- Display Encryption cipher
 get compproc		-- Display Compression scheme
 get compwinsize		-- Display Compression Window Size
 get config		-- Display Current AP Configuration
 get countrycode		-- Display Country Code
 get cpuload		-- Get CPU usage 
 get connstate		-- Display Connected state(AP Client Mode)
 get ctsmode		-- Display CTS mode
 get ctsrate		-- Display CTS rate
 get ctstype		-- Display CTS type
 get crate		-- Display Current Data Rate of AP Client with Remote AP
 get cstrength		-- Display Current Signal Strength of AP Client with Remote AP
 get dhcpc		-- Display DHCP Client State
 get diap		-- Display DIAP State
 get domainsuffix		-- Display Domain Name Server suffix
 get dtim		-- Display Data Beacon Rate (DTIM)
 get enableANI		-- Display Adaptive Noise Immunity Control On/Off
 get encryption		-- Display Encryption Mode
 get eth2wlan		-- Display Eth2Wlan Broadcast packet filter state
 get extendedchanmode		-- Display Extended Channel Mode
 get factory		-- Display Factory Setting
 get firStepLvl		-- Display ANI Parameter for FirStepLevel
 get fragmentthreshold		-- Display Fragment Threshold
 get frequency		-- Display Radio Frequency (MHz)
 get gateway		-- Display Gateway IP Address
 get gbeaconrate		-- Display 11g Beacon Rate
 get gdraft5		-- Display 11g Draft 5.0 compatibility
 get groupkeyupdate		-- Display Group Key Update Interval (in Seconds)
 get hardware		-- Display Hardware Revisions
 get hostipaddr		-- Display Host IP Address
 get iapp		-- Display IAPP State
 get iapplist		-- Display IAPP Group List
 get iappcondition		-- Display IAPP Condition State
 get iappuser		-- Display IAPP User Limit Number
 get ipaddr		-- Display IP Address
 get ipmask		-- Display IP Subnet Mask
 get jsw		-- Display Jumpstart Mode
 get jsP2PassPhrase		-- Display JS-P2 passphrase
 get key		-- Display Encryption Key
 get keyentrymethod		-- Display Encryption Key Entry Method
 get keysource		-- Display Source Of Encryption Keys
 get lcp		-- Display LCP State
 get lcplink		-- Display Ethernet Link state
 get login		-- Display Login User Name
 get macaddress		-- Display Mac address
 get massproductiontest		-- Display massproductiontest flag
 get minimumrate		-- Display Minimum Rate
 get MulticastRateControl		-- Display MulticastRateControl
 get MulticastRateIndex		-- Display MulticastRateIndex
 get MulticastPacketControl		-- Display MulticastPacketControl
 get MaxMulticastPacketNumber		-- Display MaxMulticastPacketNumber
 get MulticastPacketNumber		-- Display current MulticastPacketNumber
 get nameaddr		-- Display IP address of name server
 get nf		-- Display Noise Floor
 get noiseImmunityLvl		-- Display ANI Parameter for Noise Immunity Level
 get ofdmTrigHigh		-- Display Higher Trigger Threshold for OFDM Phy Errors for ANI Control
 get ofdmTrigLow		-- Display Lower Trigger Threshold for OFDM Phy Errors for ANI Control
 get ofdmWeakSigDet		-- Display ANI Parameter for OFDM Weak Signal Detection
 get overRidetxpower		-- Display Tx power override
 get passphrase		-- display Passphrase
 get pktLogEnable		-- Display Packet Logging Mode
 get power		-- Display Transmit Power Setting
 get targetPower		-- Display Target Power Setting
 get controlPower		-- Display Control Power Setting
 get swPower		-- Display Software Power Setting
 get quietAckCtsAllow		-- Display if Ack/Cts frames are allowed during quiet period
 get quietDuration		-- Display Duration of quiet period
 get quietOffset		-- Display Offset of quiet period into the beacon period
 get radarChRecord		-- Display RadarChannelRecord
 get radiusname		-- Display RADIUS server name or IP address
 get radiusport		-- Display RADIUS port number
 get radiussecret		-- Display RADIUS shared secret
 get radius2ndstate		-- Display the second RADIUS Mode
 get radiusname2nd		-- Display the second RADIUS server name or IP address
 get radiusport2nd		-- Display the second RADIUS port number
 get radiussecret2nd		-- Display the second RADIUS shared secret
 get radiuscfgid		-- Display the configuration of radius now
 get accountingstate		-- Display Accounting Mode
 get accountingname		-- Display Accounting server name or IP address
 get accountingport		-- Display Accounting port number
 get accounting2ndstate		-- Display second Accounting Mode
 get accounting2ndname		-- Display second Accounting		server name or IP address
 get accounting2ndport		-- Display second Accounting port number
 get accountingcfgid		-- Display the configuration of Accounting now
 get rate		-- Display Data Rate
 get reg		-- Display the register contents at the given offset
 get remoteAp		-- Display Remote Ap's Mac Address
 get reset		-- Display # of resets
 get runtime		-- Display Runtime version 
 get hwtxretries		-- Display HW Transmit Retry Limit
 get swtxretries		-- Display SW Transmit Retry Limit
 get rtsthreshold		-- Display RTS/CTS Threshold
 get roguebsstype		-- Display ROGUE AP BSS Type
 get roguesecurity		-- Display ROGUE AP Security Type
 get roguebandselect		-- Display ROGUE AP Band Select
 get shortpreamble		-- Display Short Preamble Usage
 get shortslottime		-- Display Short Slot Time Usage
 get serviceType		-- Display Service Type
 get snmp		-- Display SNMP Agent Status
 get sntpserver		-- Display SNTP/NTP Server IP Address
 get tzonelist		-- Display Time Zone
 get daylightsaving		-- Display Day Light Saving Time
 get softwareretry		-- Display Software Retry
 get spurImmunityLvl		-- Display ANI Parameter for Spur Immunity Level
 get ssid		-- Display Service Set ID
 get ssidsuppress		-- Display SSID Suppress Mode
 get station		-- Display Station Status
 get SuperA		-- Display SuperA Feature Status
 get SuperG		-- Display SuperG Feature Status
 get systemname		-- Display Access Point System Name
 get sta2sta		-- Display wireless STAs to wireless STAs connect state
 get eth2sta		-- Display ethernet to wireless STAs connect state
 get telnet		-- Display Telnet & SSH Mode
 get timeout		-- Display Telnet Timeout
 get iappinfo		-- Display IAPP AP table Information
 get matinfo		-- Display MAT Information
 get matstate		-- Get MAT Status
 get syslog		-- Display Syslog Information
 get trap		-- Display TRAP Status
 get tzone		-- Display Time Zone Setting
 get updateparam		-- Display Vendor Default Firmware Update Params
 get upsd		-- Display UPSD Mode
 get uptime		-- Display UpTime
 get vlan		-- Display VLAN Mode
 get wlanManage		-- Display manage AP with WLAN Mode
 get vlanManage		-- Display manage AP with VLAN Mode
 get watchdog		-- Display Watchdog Mode
 get wds		-- Display WDS Mode
 get wep		-- Display Encryption Mode
 get wirelessmode		-- Display Wireless LAN Mode
 get wmm		-- Display WMM Mode
 get wmmParamBss		-- Display WMM parameters used by STA in this BSS
 get wmmParam		-- Display WMM parameters used by this AP
 get wpaie		-- Display current IE of WPA
 get wdt		-- Display current watch dog timer status
 get wlanstate		-- Display wlan state
 get xrpoll		-- Display XR poll
 get xrbss		-- Display XR Bss Info
 get xrFragmentThreshold		-- Display XR fragment threshold
 get rbcnt		-- Reset reboot counter
 get vlanstate		-- Display Vlan State State
 get nativevlan		-- Display Native Vlan Tag 
 get multi-state		-- Display Multi-SSID Mode
 get multi-ind-state [index]		-- Display Individual Multi-SSID State
 get Vlantag		-- Display Vlantag
 get multi-ssid [index]		-- Display Service Set ID for Multi-SSID
 get multi-ssidsuppress[index]		-- Display SSID Suppress Mode
 get multi-wmm[index]		-- Display WMM Mode
 get multi-authentication [index]		-- Display Authentication Type for Multi-SSID
 get multi-cipher [index]		-- Display Encryption cipher for Multi-SSID
 get multi-encryption [index]		-- Display Encryption Mode for Multi-SSID
 get multi-keyentrymethod		[index]		-- Display Encryption Key Entry Method for Multi-SSID
 get multi-vlantag [index]		-- Display Vlan-Tag for Multi-SSID
 get multi-key		-- Display Encryption Key for Multi-SSID
 get multi-keysource [index]		-- Display Key Source for Multi-SSID
 get multi-passphrase [index]		-- Display Passphrase for Multi-SSID
 get multi-acct-state		-- Display Accounting state
 get multi-idv-acct-sta [index]		-- Display Individual Accounting state
 get multi-idv-acct-srv [index]		-- Display Individual Accounting server
 get multi-idv-acct-port [index]		-- Display Individual Accounting server port
 get multi-config [index]		-- Display AP Configuration for Multi-SSID
 get mux		-- Display MUX status
 get create		-- Display F/W create time
 get ifping		-- Display Ping control status 
 help		-- Display CLI Command List
 Lebradeb		-- Disable reboot during radar detection
 ls		-- list directory
 mem		-- system memory statistics
 mv		-- Move file
 np		-- Network Performance
 ns		-- Network Performance Server
 ping		-- Ping
 pktLog		-- Packet Log
 radar!		-- Simulate radar detection on current channel
 reboot		-- Reboot Access Point
 rm		-- Remove file
 run		-- Run command file
 quit		-- Logoff
 set 11gonly		-- Set 11g Only Allowed
 set 11goptimize		-- Set 11g Optimization Level
 set 11goverlapbss		-- Set Overlapping BSS Protection
 set abolt		-- 
 set acl		-- Set Access Control List
 set wdsacl		-- Set WDS List
 set aging		-- Set Aging Interval
 set antenna		-- Set Antenna
 set apmode		-- Set AP Mode
 set authentication		-- Set Authentication Type
 set autochannelselect		-- Set Auto Channel Selection
 set basic11b		-- Set Use of Basic 11b Rates
 set basic11g		-- Set Use of Basic 11g Rates
 set basisconnect		-- Set Basis of Connect Mode
 set beaconinterval		-- Modify Beacon Interval
 set ratecontrol		-- Enable/Disable supported datarate
 set supportrate		-- Modify supported datarate(bit mask)
 set bridgelearning		-- Enable/disable bridge learning
 set burstSeqThreshold		-- Set Max Number of frames in a Burst
 set burstTime		-- Set Burst Time
 set cachePerf		-- Begin cache performance monitoring
 set calibration		-- Set Calibration Period
 set cckTrigHigh		-- Set Higher Trigger Threshold for CCK Phy Errors For ANI Control
 set cckTrigLow		-- Set Lower Trigger Threshold for CCK Phy Errors For ANI Control
 set cckWeakSigThr		-- Set ANI Parameter for CCK Weak Signal Detection Threshold
 set channel		-- Set Radio Channel
 set cipher		-- Set Cipher
 set compproc		-- Set Compression Scheme
 set compwinsize		-- Set Compression Window Size
 set countrycode		-- Set Country Code
 set ctsmode		-- Set CTS Mode
 set ctsrate		-- Set CTS Rate
 set ctstype		-- Set CTS Type
 set dhcpc		-- Set DHCP Client State
 set diap		-- Set DIAP State
 set domainsuffix		-- Set Domain Name Server Suffix
 set dtim		-- Set Data Beacon Rate (DTIM)
 set enableANI		-- Turn Adaptive Noise Immunity Control On/Off
 set encryption		-- Set Encryption Mode
 set extendedchanmode		-- Set Extended Channel Mode
 set eth2wlan		-- Set Eth2Wlan Broadcast packet filter state
 set factory		-- Change Factory Setting
 set factorydefault		-- Restore to Default Factory Settings
 set firStepLvl		-- Set ANI Parameter for FirStepLevel
 set fragmentthreshold		-- Set Fragment Threshold
 set frequency		-- Set Radio Frequency (MHz)
 set gateway		-- Set Gateway IP Address
 set gbeaconrate		-- Set 11g Beacon Rate
 set groupkeyupdate		-- Set Group Key Update Interval (in Seconds)
 set gdraft5		-- Set 11g Draft 5.0 compatibility
 set snmp		-- Set		SNMP Agent Status
 set iapp		-- Set IAPP State
 set iappcondition		-- Set IAPP Phase State
 set iappuser		-- Set IAPP User Limit Number
 set hostipaddr		-- Set Host IP address
 set ipaddr		-- Set IP Address
 set ipmask		-- Set IP Subnet Mask
 set jsw		-- Set Jumpstart Mode
 set jsp2Passwd		-- Set JS-P2 password
 set key		-- Set Encryption Key
 set keyentrymethod		-- Select Encryption Key Entry Method
 set keysource		-- Select Source Of Encryption Keys
 set lcp		-- Set LCP State
 set login		-- Modify Login User Name
 set mac		-- Set Mac Address
 set rbcnt		-- Reset reboot counter
 set matstate		-- Set MAT Status
 set syslog		-- Set sysLog settings
 set syslog_test		-- Set Radio Channel
 set trap		-- Set Trap Status
 set massproductiontest		-- Set massproductiontest flag
 set minimumrate		-- Set Minimum Rate
 set minimumrate		-- Set Minimum Rate
 set minimumrate		-- Set Minimum Rate
 set minimumrate		-- Set Minimum Rate
 set minimumrate		-- Set Minimum Rate
 set MulticastRateControl		-- Set MulticastRateControl
 set MulticastRateIndex		-- Set MulticastRateIndex
 set MulticastPacketControl		-- Set MulticastPacketControl
 set MaxMulticastPacketNumber		-- Set MaxMulticastPacketNumber
 set nameaddress		-- Set Name Server IP address
 set noiseImmunityLvl		-- Set ANI Parameter for Noise Immunity Level
 set ofdmTrigHigh		-- Set Higher Trigger Threshold for OFDM Phy Errors for ANI Control
 set ofdmTrigLow		-- Set Lower Trigger Threshold for OFDM Phy Errors for ANI Control
 set ofdmWeakSigDet		-- Set ANI Parameter for OFDM Weak Signal Detection
 set overRidetxpower		-- Set Tx power override
 set password		-- Modify Password
 set passphrase		-- Modify Passphrase
 set pktLogEnable		-- Enable Packet Logging
 set power		-- Set Transmit Power
 set quietAckCtsAllow		-- Allow Ack/Cts frames during quiet period
 set quietDuration		-- Duration of quiet period
 set quietOffset		-- Offset of quiet period into the beacon period
 set roguestatus		-- Set Rogue AP status
 set roguebsstypestatus		-- Set Rogue AP BSS type status
 set roguebsstype		-- Set ROGUE AP BSS Type
 set roguesecuritystatus		-- Set Rogue AP Security Type status
 set roguesecurity		-- Set ROGUE AP Security Type
 set roguebandselectstatus		-- Set Rogue AP Band Select status
 set roguebandselect		-- Set ROGUE AP Band Select
 set radarChRecord		-- Display RadarChannelRecord
 set radiusname		-- Set RADIUS name or IP address
 set radiusport		-- Set RADIUS port number
 set radiussecret		-- Set RADIUS shared secret
 set radius2ndstate		-- Set the second RADIUS Mode
 set radiusname2nd		-- Set the second RADIUS name or IP address
 set radiusport2nd		-- Set the second RADIUS port number
 set radiussecret2nd		-- Set the second		RADIUS shared secret
 set accountingstate		-- Set Accounting Mode
 set accountingname		-- Set Accounting name or IP address
 set accountingport		-- Set Accounting port number
 set accounting2ndstate		-- Set second Accounting Mode
 set accounting2ndname		-- Set second Accounting name or IP address
 set accounting2ndport		-- Set second Accounting port number
 set rate		-- Set Data Rate
 set rate		-- Set Data Rate
 set rate		-- Set Data Rate
 set rate		-- Set Data Rate
 set rate		-- Set Data Rate
 set reg		-- Set Register Value
 set regulatorydomain		-- Set Regulatory Domain
 set remoteAP		-- Set Remote AP's Mac Address
 set hwtxretries		-- Set HW Transmit Retry Limit
 set swtxretries		-- Set SW Transmit Retry Limit
 set rtsthreshold		-- Set RTS/CTS Threshold
 set shortpreamble		-- Set Short Preamble
 set shortslottime		-- Set Short Slot Time
 set serviceType		-- Set Service Type
 set sntpserver		-- Set SNTP/NTP Server IP Address
 set tzone		-- Set Time Zone Setting
 set daylightsaving		-- Set Day Light Saving Time
 set softwareretry		-- Set Software Retry
 set spurImmunityLvl		-- Set ANI Parameter for Spur Immunity Level
 set ssid		-- Set Service Set ID
 set ssidsuppress		-- Set SSID Suppress Mode
 set SuperA		-- Super A Features 
 set SuperG		-- Super G Features 
 set systemname		-- Set Access Point System Name
 set sta2sta		-- Set wireless STAs to wireless STAs connect state
 set eth2sta		-- Set ethernet to wireless STAs connect state
 set updateparam		-- Set Vendor Default Firmware Update Params
 set upsd		-- Set UPSD Mode
 set vlan		-- Set VLAN Mode
 set wlanManage		-- Set manage AP with WLAN Mode
 set vlanManage		-- Set manage AP with VLAN Mode
 set watchdog		-- Set Watchdog Mode
 set wds		-- Set WDS Mode
 set wep		-- Set Encryption Mode
 set wlanstate		-- Set wlan state
 set wirelessmode		-- Set Wireless LAN Mode
 set wmm		-- Set WMM Mode
 set wmmParamBss		-- Set WMM parameters used by STAs in this BSS
 set wmmParam		-- Set WMM parameters used by this AP
 set supermode		-- Display Factory Setting
 set wdt		-- Set Watch Dog Timer
 set stoptoggle		-- Set stop to toggle Watch Dog Timer
 set onoff		-- diagnosis to on/off Watch Dog Timer status
 set xr		-- Set XR
 set vlanstate		-- Set Vlan State State
 set nativevlan		-- Set Native Vlan Tag 
 set multi-state		-- Set Multi-SSID Mode
 set multi-ind-state		-- Set Individual Multi-SSID State
 set Vlantag		-- Modify Vlantag
 set multi-ssid		-- Set Service Set ID for Multi-SSID
 set multi-ssidsuppress		-- Set SSID Suppress Mode
 set multi-wmm		-- Set WMM Mode
 set multi-authentication		-- Set Authentication Type for Multi-SSID
 set multi-cipher		-- Set Cipher for Multi-SSID
 set multi-encryption		-- Set Encryption Mode for Multi-SSID
 set multi-keyentrymethod		-- Select Encryption Key Entry Method for Multi-SSID
 set multi-vlantag [tag value] [index] -- Set Vlan-Tag for Multi-SSID
 set multi-key		-- Set Encryption Key for Multi-SSID
 set multi-passphrase		-- Set PassPhrase for Multi-SSID
 set multi-acct-state		-- Set Accounting state
 set multi-idv-acct-sta		-- Set Individual Accounting state
 set multi-idv-acct-srv [index]		-- Set Individual Accounting server
 set multi-idv-acct-port [index]		-- Set Individual Accounting server port
 set telnet		-- Set Telnet & SSH Mode
 set timeout		-- Set Telnet Timeout
 set ifping		-- Set ping Allowed to enable or disable
 spy report		-- Print spy report
 spy start		-- Start spy
 spy stop		-- Stop spy
 start wlan		-- Start the current wlan
 stop wlan		-- Stop the current wlan
 ssh showalgorithm		-- Show SSH Algorithm
 ssh setalgorithm		-- Set SSH Algorithm		< Algorithm<0..13>(0:3DES/1:AES128/2:AES192/3:AES256/4:Arcfour/5:Blowfish/6:Cast128/7:Twofish128/8:Twofish192/9:Twofish256/10:MD5/11:SHA1/12:Password) Status<string>(enable/disable) >
 ssh showuser		-- Show SSH User
 ssh setrekey		-- Set SSH Rekey		< Time<0..3>(0:10Min/1:30Min/2:60Min/3:Never) >
 ssh loaddefault		-- Load SSH Default Setting
 timeofday		-- Display Current Time of Day
 version		-- Software version
 rstp setstp		-- Modify Spanning Tree Settings
 rstp getstp		-- Show Spanning Tree Settings
 rstp setport		-- Modify STP Port Settings
 rstp getport		-- Show STP Port Settings
 rstp getdesc		-- Show STP Port Description
 rstp setstate		-- Modify Spanning Tree State
 rstp getstate		-- Show Spanning Tree State 
 rstp setdefault		-- Set Factory Default
 rstp settest		-- Set To Test Configuration
 rstp setdbg		-- Set Test Debug Level
 rstp setfilter		-- Set Filter Debug Level
 snmp adduser		-- Add User To SNMP Agent
 snmp deluser		-- Delete User From SNMP Agent
 snmp showuser		-- Show User In SNMP Agent
 snmp setauthkey		-- Set User Auth Key
 snmp setprivkey		-- Set User Private Key
 snmp addgroup		-- Add User Group
 snmp delgroup		-- Delete User Group
 snmp showgroup		-- Show User Group
 snmp addview		-- Add User View
 snmp delview		-- Delete User View
 snmp showview		-- Show User View
 snmp addcomm		-- Add Communication String
 snmp editpubliccomm		-- Edit Communication String
 snmp editprivatecomm		-- Edit Communication String
 snmp delcomm		-- Delete Communication String
 snmp showcomm		-- Show Communication String
 snmp addhost		-- Add Host To Notify List
 snmp delhost		-- Delete Host From Notify List
 snmp showhost		-- Show Host In Notify List
 snmp authtrap		-- Set Auth Trap Status
 snmp sendtrap		-- Send Warm Trap
 snmp status		-- Display SNMP Agent status
 snmp suspend		-- Suspend SNMP Agent
 snmp resume		-- Resume SNMP Agent
 snmp load_default		-- Load SNMP Default Setting
 snmp location		-- Set SNMP Location
 snmp showlocation		-- Display SNMP Location
 tftp get		-- Get a file from TFTP Server.
 tftp secget		-- Securely get a file from TFTP Server.
 tftp uploadtxt		-- Upload the configuration of the device to TFTP Server.
 tftp secuploadtxt		-- Securely upload the configuration of the device to TFTP Server.
 tftp srvip		-- Setup the TFTP Server IP address.
 tftp update		-- Update the file to the device.
 tftp info		-- Information about the TFTPC setting.
 ssl get		-- Get a file from TFTP Server.
 ssl ftpsrv		-- Set FTP Server IP Address.
 ssl usrpwd		-- Set the user name and password for Loginning to FTP Server.
 ssl info		-- Display the information of the ssl.
D-Link Access Point wlan1 ->